Ford axle identification.

Dana 44, 60, 70, and 80 axles have 10 bolts around the rear cover and the fill plug is in the cover. Dana 44 axles use a 1/2" wrench on the cover and Dana 60's use a 9/16" wrench, if I remember right. If the front axle is a solid (not IFS/TTB) axle and has kingpins, it is likely a Dana 60. If it has ball-joints, it could be either a 44 or 60.The Dana 44 front and 28-spline Ford 9-inch rear axle found in later Broncos had little trouble coping with these moderately sized tires considering the off-road demands of the day. What was ...1987 - 1996 F150 & Larger F-Series Trucks - front axle identification - Can't seam to figure out what front diff I have looking to get one of the new fancier diff covers if anyone know I would appreciate it...Dec 29, 2010 · 409 = Print Number (Model Number) B = Revision Identifier (Change in Design) 3L73: 3L73 = 3.73 Ratio. L = Limited Slip. Absence of L = Open Differential. A 3.73 geared limited slip axle would be marked as : 3L73. An open differential would show 3 (space)73. 102 denotes the ring gear size. 10.25 inches. Axle Identification Chart. DANA 25/27 These Danas are indistinguishable in appearance. The military Model 25 has a thick, cast cover, while the 27 and civilian-model 25s have a thinner cover, will accept taller gears, and backed V-6s. DANA 28 The alloy-case Dana 28, with a 6 5/8-inch-diameter ring gear, came in Bronco IIs and Rangers with ...

Received 9 Likes on 9 Posts. They are both 76 Truck D6TA. The front one has a 4.09 gear and the rear has 4.10. Both appear to be open differentials since there is no L after the 4 (4L10 is limited slip) The axle code is B4, which would indicate LS in the rear. The rear is a Dana 60, the front is probably a Dana 44.Originally Posted by BigBlue 94. My 99 e250 has a 24 axle code. I know it's an open 3.73 Dana 60. That follows ford code with a 2 digit numbered axle code being open and a letter /number digit code for limited slip. 1959 thru today: Two digit AXLE code. If the first digit is a letter: Limited Slip.

Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle Identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines.

The Dana 44 was introduced after World War II and is commonly found under the front and rear of a wide variety of vehicles. Starting in 1972, modern factory Dana 44’s had 30-spine axle shafts with a thickness of 1.31 inches (earlier axles were 10- or 19-spline). Spicer (Dana) 44 axles use an 8-1/2-inch ring gear bolted to the carrier by 10 ...Quick ID guide for the Ford 8 in. and 9 inch rear axle. We look at how to determine Equa lok, traction lok and open differentials. We show the best and worst...78/79 Ford Dana 60 Front Axle ID help: I have what I'm 99% sure is a 78/79 high pinion Dana 60 front axle. It's open knuckle, king pins, spring perches are 31.5" apart, big knuckles, the codes stamped into the axle tube match up. The problem is where the "60" is supposed to be cast into the housing, there's an "NC" inside a diamond.1985-1991 Ford F350 Dana 60 Identification. The open knuckle, monobeam, Dana-Spicer Model 60 was reintroduced by Ford as a mid-year design change in the 1985 model year F-350 1 ton 4x4, replacing the Twin Traction Beam IFS Dana 50 4600 pound rated axle which was used on F-350 trucks starting in the 1980 model year.if your rear end is a full floater (large hub sticking out in center of wheel) than you likely have a F250 heavy duty, meaning the front axle is a Dana 50. if your rear end is a semi floater (flat in center of wheel - no hub) than you likely have a standard F250, meaning the front axle is a Dana 44. Reply Like. # 5.

and you cant put 31 spline axles in a 28 spline housing. bearings sizes are different. 79-93 is one length, 94-98 is one length and 99-04. All explorers and trucks with an 8.8 had a 31 spline trac lock. There was no such thing as an 8.8 until 1983. Not all F150's and Explorers have Trac-Lok, as it's an option.

Location. Colorado. They never put a big bearing under an EB until like 74 or 75. A 60's vintage EB will have a 9" in the rear with most likely a Dana 30 up front. If the tag on the 9" is gone and so is the VIN tag, then there really isnt a way to tell what the gears are without opening it up.

Decoding Ford rear axle codes can be a bit complex, but by following a step-by-step process, it becomes much easier. Each letter and number in the rear axle code has a specific meaning, allowing you to extract valuable information about your axle. For example, the first two letters of the code indicate the axle's size and capacity, while the ...Ford Rear Axle Assembly Identification - Page 09: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines ... Ford Pass. 79-82 Lincoln & Town Car 80-81 Lincoln & Town Car '82 Mercury 80-82: 2.73: 8.5: NL: 28-WGY-A2: Ford Pass. 82-83 Lincoln & Town Car '82-83 Mercury 82-83: ...By decoding the axle code, you can determine the specific axle ratio of your Ford F150 truck. Examples: Here are a few examples to illustrate the relationship between axle codes and axle ratios: Axle Code – 3.55: Axle Ratio – 3.55. Axle Code – 4.10: Axle Ratio – 4.10. Axle Code – 3L: Axle Ratio – 3.15 (Limited Slip)A Ford Axle Code is a series of letters and numbers that is used to identify the specific axle installed in a Ford vehicle. It provides important information such as the …The Mustang II utilizes two different style rear axles. The first axle is used on 4cyl and some 6cyl cars and is a 6 3/4" ring gear integral carrier axle. The second is used on some 6cyl and all 8cyl cars and is an 8" ring gear removable carrier axle. The two axles are easy to tell apart. Looking at the axle from the rear of the car, if the ...The Following Is a List of Common Dana 61 BOM Numbers - These Axles are NOT Dana 60 Axle: 603925-1. 603946-1. 605022-17. 605039-7. 605064-4.Ford Rear Axle Assembly Identification - Page 01. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.

Ford Rear Axle Assembly Identification - Page 17: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V106A: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106B: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106C: Ford F250 Pickup ...Ford Rear Axle Assembly Identification - Page 08: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WFG-A: Ford Pass., Mercury '70-74: 2.75: 9 in: L: 28-WFG-A: Ford Pass., Mercury 70-74:May 15, 2021 · How can you identify which rear axle you have? It can be narrowed down this way:1. Rear brake drum backing plate - Finding the number etched in2. The rear ax... Nothing you need to worry about unless you bought a set for a 92 or older. even then you would just get the matching yoke. Ford 10.25 & 10.50-Inch Axle Tips - Axle Examination. The 93-97 10.25 gear set is the same dimensions as a 10.5 set, except that inner bearing. 98 TJ LQ4/TH400.Mar 24, 2023 ... Kansas Farm Auction Action! 1950s, 60s 70s & 80s Cars, Trucks, Tractors & more! Old Ford & Chevrolet. Mr. Goodpliers New 20K views · 30:13 &midd...Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle Identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines.I am wondering what kind of axles are under my truck. It is a 1986 F-250 6.9 idi 4x4, I found the axle codes but am having some trouble figuring out what exactly they are. Front axle:3.54 e6ta 610254-1. Rear axle: v127a 3l55 10 2 5k11. I know it has 3.55 limited slip gears but am curious weather these are Ford or Dana axles and if so what model.

Decoding Ford axle tag codes is crucial for identifying the specific axle installed in a vehicle, making accurate repairs and upgrades, and conducting vehicle …

The Ford Sterling 10-1/2" Rear Full-Floating Axle was introduced in 1999 along with the new Super Duty F250 and F350. It shares some parts with the similar 10-1/4" Sterling Rear Axle which Ford used from 1985 to 1997 in the F250 and F350. The 10-1/2" Sterling is equipped with disc brakes (with the possible exception of some very early ...1973 - 1979 F-100 & Larger F-Series Trucks - Dana 60 and Dana 70 Axle ID Help - I just picked up a Dana 70 dual wheel rear end (4.56 gears) and also a Dana 60 single wheel rear end (4.10 gears) and I'm trying to identify what vehicle (and year) these came out of. ... I've only messed with Ford 8" and 9" third members, where they are removable ...Reply With Quote. Assuming a its got Ford PCD, the pigs head looks like an English See Burtons catalogue. I eat to survive. I drink to forget. I ...Ford design rear axles contain a synthetic lubricant that does not require changing unless you submerge the axle in water. 2 Ford recommends using Motorcraft (Ford) DOT 3 LV High Performance Motor Vehicle Brake Fluid, Motorcraft (Ford) DOT 4 LV High Performance Motor Vehicle Brake Fluid or equivalent meeting WSS-M6C65-A1 or WSS-M6C65-A2.Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle ID. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:Decoding the Ford 9" Axle Tag. Using the information I found on DIY Ford, I created the following image which represents my attempt to decode the tag I found on the rear axle in my '76 F-150 LWB 4X2. I think that I have figured out the date of manufacture, ratio and presence of a limited slip differential.Though flying ants and termites look similar, these pests require very different treatments. Learn more with Today's Home Owner’s guide to flying ants vs termites. Expert Advice On...1973-1979 Ford Truck Front Axle Codes. The third digit of the axle code identifies the ratio and/or capacity of the front axle, if applicable. NOTE: This section is transcribed in it's entirety from the Ford MPC and will include listings not used on F100/350 trucks. Adjustable strg. column w/power strg. Adjustable strg. column w/power strg.1 / 1. 2015 - 2020 Ford F150 - Front axle housing identification - I am looking at purchasing a front axle housing to allow me to set up my replacement gears and Torrsen differential prior to disassembling the front axle. When i look the part up I keep coming up with two part numbers. The first one being NL3Z-3010-A and the...Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Dana Axel Identification. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:

The Ford 8.8 Rear Axle Is Cheaper Than a 9-Inch. 10) Most 8.8 axletubes are 3 inches in diameter and very thin. To prevent warping from heat, don't use a torch and avoid extended use of a die ...

AXLE 37J: 37 = Dana 60 / 3.54-1 / No Limited Slip // J = Power Steering. IF the AXLE code stamped on the Warranty Plate begins with a letter: Limited Slip. If with a number, no Limited Slip. 1973 - 1979 F-100 & Larger F-Series Trucks - Axle Identification help and LSD Info - Finally able to get to work on my new 78'!

Ford Rear Axle Assembly Identification - Page 14. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.All Dana axles have a Bill of Materials (BOM) number stamped into the long axle tube that can be used to look up many of the axle's important details including the gear ratio, ring gear rotation, differential type and spline count, as …The BOM number is what we use to positively identify your axles build configuration. 2005-2016 Ford Super Duty Dana 60 front axles will have the following characteristics: Coil Spring, 3 Link Front Suspension with two long radius arms behind the axle, and a tracking bar between axle and frame. 10 Bolt Differential Cover; Differential Cover is ...Jul 5, 2021 · 2017+ Super Duty - Which rear axle do I have - 2019 F250 6.2 4wd with a 3E axle code. ... 2017+ Super Duty The 2017+ Ford F250, F350, F450 and F550 Super Duty Pickup ... Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V012-A: Ford Pass., Mercury 86-91: 2.73: 8.8 Identifying the rear axle in a Ford vehicle is crucial for various reasons, such as determining the appropriate gear ratio for optimal performance and ensuring …Ford for 2006 MY applied the "wide trac" front axle (Dana Super 60) to the Super Duty Pickup trucks. It was applied under the "TOW BOSS" package ONLY for the 6.0L F350 DRW trucks with an automatic transmission. Yes, you might get 3.73, 4.10 or 4.30 gears using the 6.0L, 5.4L, or 6.8L motors and other transmissions. The Dana 44 was introduced after World War II and is commonly found under the front and rear of a wide variety of vehicles. Starting in 1972, modern factory Dana 44’s had 30-spine axle shafts with a thickness of 1.31 inches (earlier axles were 10- or 19-spline). Spicer (Dana) 44 axles use an 8-1/2-inch ring gear bolted to the carrier by 10 ... axle identification. I think I answered my own question. I did a search over on the ford-diesel.com site and found a lot of info. I seems the tag on the axle has either a 229 or 248 and the 229 is a D50 and the 248 is a D60. I have the 248 or D60 axle. I guess this is correct. 1980-1996 Ford F-250 Dana 44IFS Front Axle Identification IDN-136 $0.00 Ford was the only vehicle manufacturer to use Dana Twin Traction Beam® Independent Front Suspension Axles which can be found on 1980-1997 model year Ford 4x4s. Ford Truck Enthusiasts Forums > Older, Classic & Antique Trucks > 1973 - 1979 F-100 & Larger F-Series Trucks > ... Axle identification. My F350 doesn't have a code on the aluminum door tag for the rear axle, my F250 doesn't have an aluminum door tag (doesn't even have doors... or a cab) and niether of my F150s have codes for the front axles (I ...

The 1957-1959 Ford styling revolution brought such cars as the Mystere show car and the Skyliner. See pictures and learn all about 1957-1959 Ford styling. Advertisement The 1957 st...1999 Ford Mustang Axle Information & Ratios. Your Mustang will be equipped with a Vehicle certification label on the driver's side door jam. This label will show your axle code under the "AX" slot. All axles for these years are integral carrier type axles, however they will come in two sizes; a 7.5 inch and an 8.8 inch.VIN can ID rear axle ratio - Call Ford (800) 392-3673. The representative was quite cordial and read everything to me from the Ford database. Confirmed the rear axle ratio, color etc. ... Rear axle ID tag located under one of the bolts that retains the inspection cover to housing or on a label that is glued on. Reply LikeInstagram:https://instagram. marina squerciati salary per episodecemu games not showing upedm concerts okchot shots arena Ford Rear Axle Assembly Identification - Page 01: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WBG-E : Ford Truck '63-71 F100: 3.70: 9 in: NL: 28-WBG-F : Ford Truck '63-71 F100: 3.89: 9 in: NL: 28-WBG-H: Ford Truck ...1 / 1. 1973 - 1979 F-100 & Larger F-Series Trucks - 28 spline , 31 spline axle identification - my questions isn't 73-79 specific, but i am working on a 76 f100 shortbed so i thought i'd post it here. i was told a while back by a ford guy that you could tell if an axle was 28 or 31 by looking at the end. i believe he said... edc all are welcome herejimmy here real name 3J axle code. My understanding is that 3J = 3.55 Electronic Locking. I'm looking at changing the rear and front axle fluid per the owners manual but wasn't sure if I had limited slip. Manual says 5.8 pints of Motorcraft 80W-90 premium rear axle lubricant for the front axle and 6.9 pints of Motorcraft 75W-140 synthetic rear axle lubricant for ... jerika cbs news Ford/Sterling 10.5, a Dana rear axle was never an option in a SRW Superduty until 2017. Its a 3.73 open differential going by the door code. That is a 10.5 with a 3.73 open diff. Some of the numbers on the tag are obscured by the bolt and rtv sealant. The 10.5 was the only axle available for an F250 in that year.Looking to identify my front axle, these are pictures of the tag. Tag is very dirty making it hard to read. Ford: D7TA-ANA / Dana: 603808-9 = Dana 44.7F Front Driving Axle / 3.50-1 / Free Running Hubs / No Limited Slip / 3,500 lbs. Capacity. Tag is very dirty making it hard to read.